Register Hello & Welcome to AndroidTablets.net, is this your first visit?

Results 1 to 7 of 7
Thanks Tree1Thanks
  • 1 Post By Dawnstar

Thread: Problem with my copy of Cube U30GT (H)

  1. #1
    Junior Member Achievements:
    100 Experience Points 31 days registered 7 days registered

    Member #
    124566
    Join Date
    Jun 2012
    Location
    Singapore
    Posts
    5

    Problem with my copy of Cube U30GT (H)

    Hi,

    There are some problems with my Cube U30GT (H) model.

    1. The wifi is acting very erratic. Sometime it works properly, sometimes it just refuse to be found by Android. The 'Turning on Wifi Device' would be permanently on.

    2. I wanted to reset the system so I can flash the firmware to v1.06 Jelly bean. However, the "Volume Up + Power on" buttons combination don't work. If I do that, the tablet will be permanently black and I have to wait for about 30 minutes before I can even turn it on again. The Rockchip flasher is unable to sense the tablet as being ready to be flashed.

    Anyone has similar problems and found a solution to it?

  2. # ADS
    Ads
    Circuit advertisement
    Join Date
    Always
    Location
    Advertising world
    Posts
    Many

  3. #2
    Junior Member Achievements:
    100 Experience Points 31 days registered 7 days registered

    Member #
    124566
    Join Date
    Jun 2012
    Location
    Singapore
    Posts
    5
    Up for assistance.

  4. #3
    Junior Member Achievements:
    100 Experience Points 31 days registered 7 days registered

    Member #
    124566
    Join Date
    Jun 2012
    Location
    Singapore
    Posts
    5
    Anyone can help?

  5. #4
    Senior Member Achievements:
    1,000 Experience Points 3 months registered 500 Experience Points 31 days registered 250 Experience Points

    Member #
    140313
    Join Date
    Sep 2012
    Location
    United Kingdom
    Posts
    279
    Thanked
    31 times
    Device
    Samsung GalaxyTab2
    Quote Originally Posted by yaoting View Post
    Hi,

    There are some problems with my Cube U30GT (H) model.

    1. The wifi is acting very erratic. Sometime it works properly, sometimes it just refuse to be found by Android. The 'Turning on Wifi Device' would be permanently on.

    2. I wanted to reset the system so I can flash the firmware to v1.06 Jelly bean. However, the "Volume Up + Power on" buttons combination don't work. If I do that, the tablet will be permanently black and I have to wait for about 30 minutes before I can even turn it on again. The Rockchip flasher is unable to sense the tablet as being ready to be flashed.

    Anyone has similar problems and found a solution to it?
    Hello

    It sounds to me you are doing it wrong, (turn off your Cube) then press the buttons also follow this guild

    First you will need a RKBatchTool_1.5.exe to install on your PC only. then you need the JB 10.4 then the update JB 10.6

    This guild works because i have the same Cube.

    1. Shut down your tablet

    2. Plug the USB cable into your tablet and connect the other end of the USB cable to your PC

    3. Now pressing the power button and volume + buttons together

    4 Once Windows notices a new device release the 2 buttons

    5. When asked for drivers browse to the “drivers” folderwithin the extractedbatch tool folder and select it allowing windows to installthe driver. If youaren't asked for drivers and you get a device install failurego to DeviceManager and look for Unknown Device. Right click on this and selectupdatedrivers. Browse to the folder within the RKBatchTool folder with thedriversfor your OS (Win 7 64 bit in my case) and select this folder.

    6. If all ok the "device 1 connected" squarewithin theRKBatchTool_1.5 will change from grey to green

    7. Press the “upgrade” button in RKBatchTool_1.5

    8. The green square should change to orange showing that theflash operationis happening

    9. If all ok you should get a success message at the end(takes about 3minutes)

    10. The tablet should reboot but if it does not then pressthe power button

    11. The first boot after an upgrade takes much longer than anormal boot. Justbe patient and wait for the lockscreen.

    12. The default language will be Chinese. When you get aprompt hit the homebutton and then go to settings and look for the menu optionwith a letter A in a white box (this is language). Select this and then the topoption on theright hand side of the screen. This will give you a list of languages. Select English (UK) or whatever and then restart the tablet.

    Done

    The files you need

    1. unzip then use batch tool to install to desktop on PC then use the other driver below in order
    https://dl.dropbox.com/u/106697397/R..._Tool_v1.5.zip

    2. Unzip (Desktop rar) to your desktop PC in the 104 folder is the JB driver (U30GT-H_Android4.1_V1.04_20120803) this will be in chinese install this driver first read (12) of the guild you must select English.
    https://dl.dropbox.com/u/106697397/Desktop.rar

    3. Then unzip (kasty-cube_u30gt_h-41-106) folder this is the update to JB it turns your tablet to full English verson v1.0.6
    https://dl.dropbox.com/u/106697397/k...t_h-41-106.zip

    Last edited by Dawnstar; 09-19-2012 at 12:30 PM.
    wurzle thanked this.

  6. #5
    Junior Member Achievements:
    100 Experience Points 31 days registered 7 days registered

    Member #
    145949
    Join Date
    Oct 2012
    Location
    Nigeria
    Posts
    1
    Device
    Cube U30GT-H

    Cube U30GT-H will not boot up to lock screen

    Quote Originally Posted by Dawnstar View Post
    Hello

    It sounds to me you are doing it wrong, (turn off your Cube) then press the buttons also follow this guild

    First you will need a RKBatchTool_1.5.exe to install on your PC only. then you need the JB 10.4 then the update JB 10.6

    This guild works because i have the same Cube.

    1. Shut down your tablet

    2. Plug the USB cable into your tablet and connect the other end of the USB cable to your PC

    3. Now pressing the power button and volume + buttons together

    4 Once Windows notices a new device release the 2 buttons

    5. When asked for drivers browse to the “drivers” folderwithin the extractedbatch tool folder and select it allowing windows to installthe driver. If youaren't asked for drivers and you get a device install failurego to DeviceManager and look for Unknown Device. Right click on this and selectupdatedrivers. Browse to the folder within the RKBatchTool folder with thedriversfor your OS (Win 7 64 bit in my case) and select this folder.

    6. If all ok the "device 1 connected" squarewithin theRKBatchTool_1.5 will change from grey to green

    7. Press the “upgrade” button in RKBatchTool_1.5

    8. The green square should change to orange showing that theflash operationis happening

    9. If all ok you should get a success message at the end(takes about 3minutes)

    10. The tablet should reboot but if it does not then pressthe power button

    11. The first boot after an upgrade takes much longer than anormal boot. Justbe patient and wait for the lockscreen.

    12. The default language will be Chinese. When you get aprompt hit the homebutton and then go to settings and look for the menu optionwith a letter A in a white box (this is language). Select this and then the topoption on theright hand side of the screen. This will give you a list of languages. Select English (UK) or whatever and then restart the tablet.

    Done

    The files you need

    1. unzip then use batch tool to install to desktop on PC then use the other driver below in order
    https://dl.dropbox.com/u/106697397/R..._Tool_v1.5.zip

    2. Unzip (Desktop rar) to your desktop PC in the 104 folder is the JB driver (U30GT-H_Android4.1_V1.04_20120803) this will be in chinese install this driver first read (12) of the guild you must select English.
    https://dl.dropbox.com/u/106697397/Desktop.rar

    3. Then unzip (kasty-cube_u30gt_h-41-106) folder this is the update to JB it turns your tablet to full English verson v1.0.6
    https://dl.dropbox.com/u/106697397/k...t_h-41-106.zip


    Hello,

    I love your post and that now makes me feel you can help me. I was trying to send an app from my Cube U30GT-H tablet to my android note and then my U30GT-H just went off, on powering it up, I discovered it will boot to the lock screen and then automatically restart itself and then continues to boot (load) endlessly without showing the lock screen again. Please, can you advise on what to do and how to go about it? My intention is to reset or flash it but do not know how to go about that. I'm a newbie to android tabs and would really appreciate any help you could render.

    Many thanks,

    Ayodele

    NOTE

    I was able to solve the problem, I connected my CUBE just as you illustrated above and then upgraded the firmware with kasty-cube_u30gt_h-41-106 though I spiked the use of Desktop rar and guess what, my CUBE is now working.
    Thanks a million.
    Last edited by dawoyo; 10-01-2012 at 07:35 PM.

  7. #6
    Junior Member
    Member #
    163624
    Join Date
    Jan 2013
    Posts
    1
    Quote Originally Posted by yaoting View Post
    Anyone can help?
    Try to press the right up corner between two fingers when using the Wi-Fi. If thé wifi is no more or less erastic I know the route cause of the problem.
    Contact me. Christophe, france
    Christophe31@orange.fr

  8. #7
    Junior Member
    Points: 120, Level: 2
    Level completed: 40%, Points required for next Level: 30
    Overall activity: 0%
    Achievements:
    7 days registered 31 days registered 100 Experience Points

    Member #
    185741
    Join Date
    Nov 2013
    Location
    Orlando, Florida USA
    Posts
    2
    Points
    120
    Level
    2
    Device
    Cube U30GT-H

    Post HELP Android not starting

    Quote Originally Posted by yaoting View Post
    Anyone can help?

    I have CUBE U30GT-H tablet that do not go Forward after chinese cube logo (and donot go to Android logo). On connecting to Computer, both drive show no files or is empty. I shows the drives on connecting to computer but as if it is wiped out. How can I restart my Android.


 

Ads:

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Similar Threads

  1. problems with cube u30gt
    By isaacdavid4 in forum Android Tablet Q&A
    Replies: 5
    Last Post: 09-20-2012, 01:37 AM
  2. No USB connection option with Cube U30GT
    By spookydad in forum Rockchip Based
    Replies: 1
    Last Post: 09-07-2012, 10:36 AM
  3. Cube U30GT
    By gpd in forum SpeMall.com
    Replies: 33
    Last Post: 08-04-2012, 04:07 AM
  4. Replies: 6
    Last Post: 07-09-2012, 10:43 AM

Search tags for this page

cube tablet not starting
,
cube u30gt hard reset
,

cube u30gt problems

,

cube u30gt usb driver

,

cube u30gt wifi fix

,

cube u30gt wifi problem

,
cube u30gt wifi problem kasty rom
,
english version u30gt-h tablet driver
,
how to hard reset cube u30gt
,
reset u30gt-h
,
u30gt reset
,

u30gt-h driver

Click on a term to search our sites for related topics.
Powered by vBulletin® Version 4.1.11
Copyright © 2014 vBulletin Solutions, Inc. All rights reserved.
Android Tablets.net is not affiliated or associated with Google, Android Project or any of the device manufacturers listed on this site.
We are simply an enthusiast site.
All times are GMT -5. The time now is 07:38 AM.