:: Inside of my SuperPad ::

SmaRkieS

Member
Apr 15, 2011
92
10
SuperPad (screwless casing)

My SuperPad is not charging anymore, I suspect that the charging port is loosen because the charger is wobbling. So I decide to open it.

Tools:

1. Prying tool (or any blunt flat object)
2. Small Philips screw driver
3. Thin plastic Card (don't use cutter/blade/knife because it will damage/slice your touch screen)
4. Tweezers (use to unlock the touch screen ribbon, and used for placing the ribbon back)

NOTE: I'm only using my webcam for the picture, sorry for the crap quality. I use this because it's fast and easy to focus.

I start using the thin plastic card on the side, slide the card on the 2nd layer of the plastic, just be careful with the plastic layer, make sure it's not the thin plastic film you peal off (see picture)

The screen is using double sided tape adhesive (see picture)

imm_2011_05_06_17_15_12_656-1.jpg




Slide the card, just follow the red line on the picture, stop on blue line where the flex cable is, or else you will cut off the flex.

imm_2011_05_06_17_09_44_578.jpg


imm_2011_05_06_17_11_28_703.jpg


imm_2011_05_06_17_15_50_828.jpg


imm_2011_05_06_17_15_12_656.jpg




The start prying next plastic layer, just pry it towards you it will unlock the plastic tabs, if you don't have any prying tools, just use any plastic tools, don't use metal tools because it will damage the casing.

imm_2011_05_06_17_14_16_765.jpg


imm_2011_05_06_17_14_52_0.jpg



- After prying it off, gently lift the screen together with the touch screen away from you where the flex ribbon of the touch screen is on the upper left, Don't fully lift the screen, because the LCD ribbon is still there.

- Unlock the Touchscreen Flex Ribbon holder, and slowly remove the flex of the touchscreen. (see picture)

- If your fingers are small you can remove the battery connector from the board, or use tweezers to remove. (see picture)

- Remove the Vibrator Motor. (see picture)

- On the main board there is a thin plastic protector, you can remove it, and remove the 4 screws on the board.

- Lift gently the board and move the board to the left, where the battery is on the left side.

- Now you can remove the LCD Connector from the board, just remove it slowly.

imm_2011_05_06_14_41_46_953-1.jpg








Main board Version.

imm_2011_05_06_15_00_25_875.jpg


imm_2011_05_06_14_46_23_906.jpg


imm_2011_05_06_14_42_21_968.jpg




The battery, 3800mAh x2.

imm_2011_05_06_15_08_36_921.jpg


imm_2011_05_06_14_41_46_953.jpg
 
Last edited:
Wifi module and antena

imm_2011_05_06_15_07_32_531.jpg


imm_2011_05_06_15_07_42_875.jpg




GPS Port, and GPS Module on main board.

imm_2011_05_06_15_06_22_531.jpg


imm_2011_05_06_15_06_50_93.jpg


Realtek Lan

imm_2011_05_06_15_03_58_890.jpg




Samsung ROM i think.

imm_2011_05_06_15_02_36_609.jpg




Hynix RAMS 256MB, no way to upgrade it.

imm_2011_05_06_14_52_00_187.jpg


imm_2011_05_06_14_52_24_953.jpg




Processor/Chipset/GPU infotMIC IMAPx210

imm_2011_05_06_14_57_46_796.jpg




HDMI Chipset.

imm_2011_05_06_14_50_05_359.jpg



Thank you for viewing my thread.

PS: I found out that the problem is the Charger Jack not the charging port, I wasted some time opening the Tablet, already fixed the charger jack and replace it with new jack.
 
Last edited:
This needs to be a sticky. These are some really good instructions.
 
Hi Smarkies,

Great post! Can you confirm where the 2Gb memory is located? As mentioned in other post, it would be an option to replace it if it was MicroSD.

R.
André
 
Nop, no microSD on the board, the NAND and RAM is soldered on the board. Flytouch2/Superpad, only the Flytouch3/Superpad2.
 
hello, is there a way to fix the, buzzing superpad 3? or it is trash,
if trash is there a way to use the lcd for secundary vga to my desktop pc?
thank you.
 
Hi, please i need help ASAP. I think i have briked my pad. Whenever i power it, it loads normally bt after all the preboot, it get stuck on a blank page where am suppose to have my desktop.I tried to flash by pressing home+vol up+power but once its powered, it just get stucked on the infotmic page and stays there forever.I also tried home+back+power button but when i press the buttom before the 5minutes timeout, its says no recovry image and that i should recover from sd.what do i do?I have also tried flashin the rom by hexing my sdcard, formatted it, then copied the files listed in android folder into it and inserted it back into my pad but when i turned it on, instead of loading the files on the card, it just load like everythin is normal. What do i do?
 
Is there a way to repair the charger Jack without opening the superpad, i have the same problem, it won't charge anymore.
 
Back
Top