i need help ... it wont go past the slide to unlock screen

mikeothe2

Member
Jul 16, 2011
3
0
I just got a Sylvania Tablets 7 in with 2.2 off some one, and it was working fine until i started installing apps , now it wont go pass the slide to unlock screen.. $Photo on 7-16-11 at 10.07 AM.jpg

I tried using a mouse and keyboard but it did now work .I also tried to reset it but i get "No recovery image is found, try recover from SD" . what sould i do?
 

cfrockit

Senior Member
Dec 26, 2010
627
191
I just got a Sylvania Tablets 7 in with 2.2 off some one, and it was working fine until i started installing apps , now it wont go pass the slide to unlock screen.. View attachment 3207

I tried using a mouse and keyboard but it did now work .I also tried to reset it but i get "No recovery image is found, try recover from SD" . what sould i do?

Welcome!

That issue is addressed at the top of this Sticky thread http://www.androidtablets.net/forum/sylvania-tablets/6437-apply-factory-reset-step-step-images.html.
Note: If you receive a "No recovery image is found, try recover from SD" message when following these steps, it is now possible to manually update the device to obtain a recovery image. http://www.androidtablets.net/forum/...rosd-card.html

Start with this Sticky thread http://www.androidtablets.net/forum...resources-synet7lp-sytabex7-disgo-6000-a.html and it will guide you to the http://www.androidtablets.net/forum...date-synet7lp-sytabex7-android-2-2-froyo.html Sticky thread to resolve your issue.

Note: Users that had previously reported getting a "No recovery image is found, try recover from SD" when attempting a "Factory Reset" (three finger method) once updated to 2.2 can Apply a factory reset - (step by step with pictures.
 
Last edited:

cfrockit

Senior Member
Dec 26, 2010
627
191
i not able to use terminal on the phone i cant factory reset.. what to do?

Without the Hardware ID "hwver" using the incorrect InfoTM Update Wrap (.ius) file may cause irreparable damage (brick) to the device.

Sylvania tablets WITH "Mini HDMI port" (pictured below) have been identified as 11.2.0.5, 11.2.0.6, 11.2.0.7 and 11.2.1.8. The most common have been 11.2.0.6 and 11.2.1.8.

$minHDMI.JPG

WITHOUT "Mini HDMI port" has been identified at the SYTABEX7 Hardware ID "hwver=11.2.1.5".

$000_0020.jpg

Depending on whether the tablet has or does not have a "Mini HDMI port" you can try to apply an update file however you risk irreparable damage to the device resulting in a brick.
 
Last edited:

mikeothe2

Member
Jul 16, 2011
3
0

cfrockit

Senior Member
Dec 26, 2010
627
191
after days of trying to get this to work i still fail.... i been stuck on step 4 on http://www.androidtablets.net/forum...date-synet7lp-sytabex7-android-2-2-froyo.html i cant get the sd card to show up on any computer i tried ... i just want this to work i hate that i wasted money ...any of things i could try? i could even have some one use TeamViewer - Free Remote Access and Remote Desktop Sharing over the Internet to try to help
mikeothe2, you're not alone there were many, many posts about users who could never get the SD card to show in the utility. To get past that issue they either used another Win32 PC/laptop, switched to the OTG USB cable method, or had a another user create the SD and forward it along. Do you have access to another Win32 computer setup to try the utility there, try another SD card or card reader, or find a male male mini USB cable?

Here's a consolidated set of steps http://www.androidtablets.net/forum...tablet-now-stuck-before-anm-logo-how-fix.html that worked to resolve a similar issue of not being able to boot or do a recovery.
 
Last edited:
Top